should and can is different on the tester and how they feel on the day. if you took the dot approval certificate and if they question it give them that and it should help your case to be ok

for this specific harness you would use the rear lower 7/16 unf mounting locations. 1 from the OEM latch receiver and the other from the lower belt mounting. due to the design these can be places below the normal harness angles as 3 points can be...

This car was imported from the US originally. Its not a Euro car on this one. I just don't get why the listing pic I show is of a US seller saying its a turbo but its 6 pin? That's what confuses me. And why I got a 7 pin I don't know haha. The...

Hey all. I need some help on this while working on my 1G NT 4G63.Refurbing the MAF system and i know the NT uses 6 pins vs Turbo 7 pins however this is where things get odd! Searching the MAF part number its coming up as a turbo MAF? But it's 6...

I got this one thats for the later evos. So 789. I thought it was worth a check to see if those worked. Just wondering if the later evo ones are weaker what they currently do for upgrading them? If they use oem ones and they fit ours and they...

The cross shaft is of a weaker design on the Evo unit vs. the DSM units. (I've posted comparison pictures several times here)The Evos are also *lighter* than the DSMs (DSM vs. Evo 1-3) which is also an obvious factor.There are other u-joints...

Awesome! Thanks alot. Looks like its a match.

Have you reached out or emailed him? Maybe he will see the email before here as sometimes people can take a while to come back here when they get busy. I sell to people and sometimes its days or even weeks before they come back on to see my...

Anyone got oem measurements? I know its got a grease nipple but this is an oem one i got and worth considering if they work for the Evos no? I mean they pushing some power also still and hold ok or they breaking them also?Anyway i got this to...

It will be a pin hole in the filler neck, or on top of the tank the rubber hose would of split. A gasket on the pump hanger could of leaked but really you just need to get down and sniff everything and possibly drop the tank to check the top of...

Big update, the entire drivetrain is finished besides the axles. Still waiting on dss for those. But happy with how everything turned out and honestly was not too bad to install. The JXB carrier bearing housing was pretty straight forward and...

Its not as bad as some other pictures i have seen but still bad none the less. I will be cleaning it up and de scaling it with methods i have found online. I will see what happens once its all back together and hope i did a good job on it all...

You'll be fine regardless. The most important change is the new ones don't leak like the originals. Sadly yours has and the solder around it has become porous. Hopefully the traces haven't failed and the voltage regulator with them. TCUs have...

Keep what you got if its working and tune for a bite more spool up. You will want a bite more power down the line anyway as most do, so allows for a bit more room to grow but you will be restricted by the turbine housing anyway so not much more...

on the side its got 3m1947 105c pet

And there was me thinking 1+1 is 2 lol, let me check the actual part number to be sure. I did just go by the big letters lol so if i pulled the buy faster then i should the whoopsie.

yup on the back it says 105c as I'm pretty sure i checked for that also. I'm not electronics expert but its crazy how much smaller it can be for the same product!

So I'm working on my 1g finally and ordered new exact OEM capacitors. Has tech come along way since as the OEM one is huge compared to the new one but its rated to the same spec? Check out the pics but its almost 4mm smaller but exactly the same...

I'm usually only cleaning it from the tailpipe and it cleans off easily with wheel cleaner and a brush. I'm also able to clean it off the o2 housing etc. with some brake cleaner or solvent like that. The wbo2 sensor gets coated just like...

Nah its just a fine like powder that burns on. I not noticed any smell from it. The ceramics tend to go red/brown vs staying while or light tan. Im not sureif i got my old plugs anymore but if i doni shall snap a pic.I have not opened up the...